• Reset the Cisco 6921 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Performing a Factory Reset

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    • User configuration settings—Reset to default values

    • Network configuration settings—Reset to default values

    • Call histories—Erased

    • Locale information—Reset to default values

    • Phone application—Erased (phone recovers by using the image in the inactive partition of flash to boot up).

     

    Before you perform a factory reset, ensure that the following conditions are met:

    • The phone must be on a DHCP-enabled network.

    • A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.

     

    To perform a factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power-up cycle.

    Step 2 While the phone is powering up, and before the Speaker button flashes on and off,

    press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in amber.

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the line buttons on the phone flash red, and the phone goes through the factory reset process.

    Do not power down the phone until it completes the factory reset process, and the main screen appears.

     

     

  • Reset the Cisco 6941 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Performing a Factory Reset

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    • User configuration settings—Reset to default values

    • Network configuration settings—Reset to default values

    • Call histories—Erased

    • Locale information—Reset to default values

    • Phone application—Erased (phone recovers by using the image in the inactive partition of flash to boot up).

     

    Before you perform a factory reset, ensure that the following conditions are met:

    • The phone must be on a DHCP-enabled network.

    • A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.

     

    To perform a factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power-up cycle.

    Step 2 While the phone is powering up, and before the Speaker button flashes on and off,

    press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in amber.

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the line buttons on the phone flash red, and the phone goes through the factory reset process.

    Do not power down the phone until it completes the factory reset process, and the main screen appears.

     

     

  • Reset the Cisco 6961 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Performing a Factory Reset

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    • User configuration settings—Reset to default values

    • Network configuration settings—Reset to default values

    • Call histories—Erased

    • Locale information—Reset to default values

    • Phone application—Erased (phone recovers by using the image in the inactive partition of flash to boot up).

     

    Before you perform a factory reset, ensure that the following conditions are met:

    • The phone must be on a DHCP-enabled network.

    • A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.

     

    To perform a factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power-up cycle.

    Step 2 While the phone is powering up, and before the Speaker button flashes on and off,

    press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in amber.

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the line buttons on the phone flash red, and the phone goes through the factory reset process.

    Do not power down the phone until it completes the factory reset process, and the main screen appears.

     

     

  • Reset the Cisco 7821 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Perform Factory Reset Phone Keypad

    Use these steps to reset the phone to factory default settings using the phone keypad.

    Procedure

    Step 1   Unplug the phone:

    If using PoE, unplug the LAN cable.

    If using the power cube, unplug the power cube.

    Step 2   Wait 5 seconds.

    Step 3   Press and hold # and plug the phone back in.

    Step 4   When the light on the Mute button and handset light strip turns off and all other lights (Line button, Headset button, Speakerphone button, and Select button) stay green, press 123456789*0# in sequence.

    When you press 1, the lights on the line buttons turn red. The light on the Select button flashes when a button is pressed.

    After you press these buttons, the phone goes through the factory reset process.

    If you press the buttons out of sequence, the phone powers on normally.

    Caution  

    Do not power down the phone until it completes the factory reset process, and the main screen appears.

     

    Perform Factory Reset from Phone Menu

    To perform a factory reset of a phone,

    Procedure

    Step 1   Press Applications.

    Step 2   Choose Admin Settings > Reset Settings > All.

    If required, unlock the phone options.

     

     

  • Reset the Cisco 7841 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Perform Factory Reset Phone Keypad

    Use these steps to reset the phone to factory default settings using the phone keypad.

    Procedure

    Step 1   Unplug the phone:

    If using PoE, unplug the LAN cable.

    If using the power cube, unplug the power cube.

    Step 2   Wait 5 seconds.

    Step 3   Press and hold # and plug the phone back in.

    Step 4   When the light on the Mute button and handset light strip turns off and all other lights (Line button, Headset button, Speakerphone button, and Select button) stay green, press 123456789*0# in sequence.

    When you press 1, the lights on the line buttons turn red. The light on the Select button flashes when a button is pressed.

    After you press these buttons, the phone goes through the factory reset process.

    If you press the buttons out of sequence, the phone powers on normally.

    Caution  

    Do not power down the phone until it completes the factory reset process, and the main screen appears.

     

    Perform Factory Reset from Phone Menu

    To perform a factory reset of a phone,

    Procedure

    Step 1   Press Applications.

    Step 2   Choose Admin Settings > Reset Settings > All.

    If required, unlock the phone options.

     

     

  • Reset the Cisco 7861 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Perform Factory Reset Phone Keypad

    Use these steps to reset the phone to factory default settings using the phone keypad.

    Procedure

    Step 1   Unplug the phone:

    If using PoE, unplug the LAN cable.

    If using the power cube, unplug the power cube.

    Step 2   Wait 5 seconds.

    Step 3   Press and hold # and plug the phone back in.

    Step 4   When the light on the Mute button and handset light strip turns off and all other lights (Line button, Headset button, Speakerphone button, and Select button) stay green, press 123456789*0# in sequence.

    When you press 1, the lights on the line buttons turn red. The light on the Select button flashes when a button is pressed.

    After you press these buttons, the phone goes through the factory reset process.

    If you press the buttons out of sequence, the phone powers on normally.

    Caution  

    Do not power down the phone until it completes the factory reset process, and the main screen appears.

     

    Perform Factory Reset from Phone Menu

    To perform a factory reset of a phone,

    Procedure

    Step 1   Press Applications.

    Step 2   Choose Admin Settings > Reset Settings > All.

    If required, unlock the phone options.

     

     

  • Reset the Cisco 7911 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power up cycle.

     

    Step 2 While the phone is powering up, and before the Applications Menu button flashes on and off, press and hold #.

    Continue to hold # until the message LED on the handset flashes on and off in sequence in red.

     

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the message LED on the handset flashes faster in red and the phone goes through the factory reset process.

     

    Do not power down the phone until it completes the factory reset process and the main screen appears.

  • Reset the Cisco 7920 Wireless IP Phone to the Factory Default

     

    Kaynak: www.cisco.com

     

    Administration options in the Network Config and Phone Settings menus are hidden by default to ensure that users do not make changes that can affect the operation of the phone. You need to start the administration mode on the phone in order to use the options.

    Start the Administration Mode on the Phone Complete these steps in order to open the administration options on the Cisco Unified Wireless IP Phone 7920 so that you can access the hidden options on the Phone menu:

    Press the Menu softkey.

    Press  * (the star key). Press  # (the pound key), and then press  # (the pound key) again.

    Press the green  green.jpg key to open the administration mode.

    Note: Power cycle the phone or press any of these keys while in the first level submenu and then press the green key to hide the options:

    any key between 0 and 9

    * key

    # key

     

    Reset the Cisco 7920 Wireless IP Phone to the Factory Default

    Complete these steps in order to reset the Cisco 7920 Wireless IP phone to the factory default:

    Choose Menu > Phone Settings > Factory Default.

    The phone displays the Restore to Default? message.

    Press the OK softkey. All settings are deleted.

    Choose Menu > Network Config in order to reconfigure the network settings for your WLAN.

     

     

  • Reset the Cisco 7925 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    Factory Reset

    You can clear all locally stored configuration options in a phone by using the Phone Settings menu. When you use the restore to factory default option, all user-defined entries in Network Profiles, Phone Settings, and Call History are erased.

    To erase the local configuration, follow these steps:

    Procedure

    Step 1 Choose SETTINGS > Phone Settings.

    Step 2 Press **2 on the keypad.

    The phone briefly displays "Start factory reset now?"

    Step 3 Press the Yes softkey. All settings are deleted.

    The phone cycles through normal startup procedures.

    Or press No to cancel the reset.

    Step 4 Press SETTINGS > Network Profiles to reconfigure the network settings for your WLAN.

     

     

  • Reset the Cisco 7941 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Complete these steps:

    Unplug the power cable from the phone, and then plug in the cable again.

    The phone begins its power up cycle.

    Immediately press and hold # and while the Headset, Mute, and Speaker buttons begin to flash in sequence, release #.

    The line buttons flash in sequence in order to indicate that the phone waits for you to enter the key sequence for the reset.

    Press 123456789*0# within 60 seconds after the Headset, Mute, and Speaker buttons begin to flash.

    If you repeat a key within the sequence, for example, if you press 123456789*0#, the sequence is still accepted and the phone resets.

    If you do not complete this key sequence or do not press any keys, after 60 seconds the Headset, Mute, and Speaker buttons no longer flash, and the phone continues with its normal startup process. The phone does not reset.

    If you enter an invalid key sequence, the buttons no longer flash, and the phone continues with its normal startup process. The phone does not reset.

    If you enter this key sequence correctly, the phone displays this prompt:

    upgrading

     

     

  • Reset the Cisco 7942G IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Performing a Factory Reset

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    • CTL file—Erased

    • LSC—Erased

    • User configuration settings—Reset to default values

    • Network configuration settings—Reset to default values

    • Call histories—Erased

    • Locale information—Reset to default values

    • Phone application—Erased (phone recovers by loading the term42.default.loads file, depending on the phone model)

     

    Before you perform a factory reset, ensure that the following conditions are met:

    • The phone must be on a DHCP-enabled network.

    • A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.

    • The term42.default.loads and the files specified in that file should be available on the TFTP server that is specified by the DHCP packet.

     

    To perform a factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power up cycle.

    Step 2 While the phone is powering up, and before the Speaker button flashes on and off,

    press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in amber.

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the line buttons on the phone flash red and the phone goes through the factory reset process.

    Do not power down the phone until it completes the factory reset process and the main screen appears.

     

     

  • Reset the Cisco 7960 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    In order to perform a factory reset of a phone if the password is set, complete these steps:

    Unplug the power cable from the phone, and then plug in the cable again.

    The phone begins its power up cycle.

    Immediately press and hold # and while the Headset, Mute, and Speaker buttons begin to flash in sequence, release #.

    The Headset, Mute, and Speaker buttons flash in sequence in order to indicate that the phone waits for you to enter the key sequence for the reset.

    Press 123456789*0# within 60 seconds after the Headset, Mute, and Speaker buttons begin to flash.

    If you repeat a key within the sequence, for example, if you press 123456789*0#, the sequence is still accepted and the phone resets.

    If you do not complete this key sequence or do not press any keys, after 60 seconds, the Headset, Mute, and Speaker buttons no longer flash, and the phone continues with its normal startup process. The phone does not reset.

    If you enter an invalid key sequence, the buttons no longer flash, and the phone continues with its normal startup process. The phone does not reset.

    If you enter this key sequence correctly, the phone displays this prompt:

    Keep network cfg? 1 = yes 2 = no

    In order to maintain the current network configuration settings for the phone when the phone resets, press 1. In order to reset the network configuration settings when the phone resets, press 2.

    If you press another key or do not respond to this prompt within 60 seconds, the phone continues with its normal startup process and does not reset. Otherwise, the phone goes through the factory reset process.

     

  • Reset the Cisco 7961 IP Phones to the Factory Defaul

     

    Kaynak: www.cisco.com

     

    Complete these steps:

    Unplug the power cable from the phone, and then plug in the cable again.

    The phone begins its power up cycle.

    Immediately press and hold # and while the Headset, Mute, and Speaker buttons begin to flash in sequence, release #.

    The line buttons flash in sequence in order to indicate that the phone waits for you to enter the key sequence for the reset.

    Press 123456789*0# within 60 seconds after the Headset, Mute, and Speaker buttons begin to flash.

    If you repeat a key within the sequence, for example, if you press 123456789*0#, the sequence is still accepted and the phone resets.

    If you do not complete this key sequence or do not press any keys, after 60 seconds the Headset, Mute, and Speaker buttons no longer flash, and the phone continues with its normal startup process. The phone does not reset.

    If you enter an invalid key sequence, the buttons no longer flash, and the phone continues with its normal startup process. The phone does not reset.

    If you enter this key sequence correctly, the phone displays this prompt:

    upgrading

     

     

  • Reset the Cisco 7962G IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Performing a Factory Reset

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    • CTL file—Erased

    • LSC—Erased

    • User configuration settings—Reset to default values

    • Network configuration settings—Reset to default values

    • Call histories—Erased

    • Locale information—Reset to default values

    • Phone application—Erased (phone recovers by loading the term62.default.loads file, depending on the phone model)

     

    Before you perform a factory reset, ensure that the following conditions are met:

    • The phone must be on a DHCP-enabled network.

    • A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.

    • The term62.default.loads file and the files specified in that file should be available on the TFTP server that is specified by the DHCP packet.

     

    To perform a factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power up cycle.

    Step 2 While the phone is powering up, and before the Speaker button flashes on and off,

    press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in amber.

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the line buttons on the phone flash red and the phone goes through the factory reset process.

    Do not power down the phone until it completes the factory reset process and the main screen appears.

     

  • Reset the Cisco 7970 IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Performing a Factory Reset

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    • CTL file—Erased

    • LSC—Erased

    • User configuration settings—Reset to default values

    • Network configuration settings—Reset to default values

    • Call histories—Erased

    • Locale information—Reset to default values

    • Phone application—Erased (phone recovers by loading the term70.default.loads file or the term71.default.loads file, depending on the phone model)

     

    Before you perform a factory reset, ensure that the following conditions are met:

    • The phone must be on a DHCP-enabled network.

    • A valid TFTP server must be set in DCHP option 150 or option 66 on the DHCP server.

    • The term70.default.loads file or the term71.default.loads file and the files specified in that file should be available on the TFTP server that is specified by the DHCP packet.

     

    To perform a factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Unplug the power cable from the phone and then plug it back in.

    The phone begins its power up cycle.

    Step 2 While the phone is powering up, and before the Speaker button flashes on and off, press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in orange.

    Step 3 Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

    After you press these keys, the line buttons on the phone flash orange and then green, and the phone goes through the factory reset process. This process can take several minutes.

    Do not power down the phone until it completes the factory reset process and the main screen appears.

     

     

  • Reset the Cisco 7975G IP Phones to the Factory Default

     

    Kaynak: www.cisco.com

     

    Factory Reset

     

    When you perform a factory reset of the Cisco Unified IP Phone, the following information is erased or reset to its default value:

    CTL file: Erased

    LSC: Erased

    User configuration settings: Reset to default values

    Network configuration settings: Reset to default values

    Call histories: Erased

    Locale information: Reset to default values

    Phone application: Erased (phone recovers by loading the appropriate default load file, which depends on the phone model term75.default.loads, term71.default.loads, term70.default.loads, term65.default.loads, or term45.default.loads)

     

    Before you perform a factory reset, ensure that the following conditions are met:

    The phone must be on a DHCP-enabled network.

    A valid TFTP server must be set in DHCP option 150 or option 66 on the DHCP server.

    The default load file for your phone model and the files specified in that file should be available on the TFTP server that is specified by the DHCP packet.

     

    To perform a factory reset of a phone, follow these steps:

    Procedure

    Step 1   Unplug the power cable from the phone and then plug it back in.

    The phone begins the power-up cycle.

    Step 2   While the phone is powering up, and before the Speaker button flashes on and off, press and hold #.

    Continue to hold # until each line button flashes on and off in sequence in orange (for the Cisco Unified IP Phone 7975G, 7971G-GE and 7970G) or amber (for the Cisco Unified IP Phone 7965G and 7945G).

    Step 3   Release # and press 123456789*0#.

    You can press a key twice in a row, but if you press the keys out of sequence, the factory reset does not take place.

    After you press these keys, the line buttons on the phone flash orange and then green (for the Cisco Unified IP Phone 7975G, 7971G-GE and 7970G) or red (for the Cisco Unified IP Phone 7965G and 7945G), and the phone goes through the factory reset process. This process can take several minutes.

    Do not power down the phone until it completes the factory reset process, and the main screen displays.

     

     

  • Reset the Cisco 8831 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    Introduction

     

    This document describes how to perform a hard factory reset on a Cisco 8831 Series IP phone, which resets all of the network and security settings of the phone.

     

    Reset the IP Phone

     

    There are two methods that you can use in order to reset the Cisco IP phone: a factory reset, and a hard factory reset.

    Factory Reset

     

    In order to perform a factory reset, navigate to Apps > Admin Settings > Reset Settings. Choose one of these options in order to reset the phone to the factory default settings:

    * All

    * Network

    * Security

     

    Hard Factory Reset

     

    If the factory reset method that is described in the previous section is not possible, then a hard reset can be attempted in order to achieve similar results. However, this method resets all of the settings directly and does not provide the option to reset only the network or security settings.

     

    Complete these steps in order to perform a hard factory reset of the phone:

     

    1) Unplug the Ethernet cable from the back side of the phone in order to power off the phone.

     

    Note: If the phone is powered through a power brick, then the power it off through the the power brick.

     

    2) Press and hold the Microphone (MIC) button on the front side of the phone:

    Continue to hold the MIC button and power on the phone (plug in the Ethernet cable or the power brick). When the lights that are located on the left, right, and back sides of the phone change from green to red, release the MIC button: 

     

    Press and hold the MIC button for approximately five seconds, and then release it. The lights should blink red twice.

     

    Press and hold the MIC button. After approximately five seconds, the lights should begin to blink red continuously, which confirms the factory reset of the phone.

     

  • Reset the Cisco 8845 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    To perform a basic factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Press Applications

    Step 2 Go to Admin settings > Reset settings > Reset device

     

    To perform a hard factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Press "#" when you power on the phone

    Step 2 You will see the headset,speaker and mute will light on and then light off.

    Step 3 When you see only headset and speaker turn on again, please press 123456789*0# in sequence.

    Step 4 After you pressed the the first digit "1", you will see speaker turn off.

    Step 5 After all the number are input completely in sequence, you will see Mute button turns on to indicate phone begin to do the factory reset.

     

     

  • Reset the Cisco 8865 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    To perform a basic factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Press Applications

    Step 2 Go to Admin settings > Reset settings > Reset device

     

    To perform a hard factory reset of a phone, perform the following steps:

    Procedure

    Step 1 Press "#" when you power on the phone

    Step 2 You will see the headset,speaker and mute will light on and then light off.

    Step 3 When you see only headset and speaker turn on again, please press 123456789*0# in sequence.

    Step 4 After you pressed the the first digit "1", you will see speaker turn off.

    Step 5 After all the number are input completely in sequence, you will see Mute button turns on to indicate phone begin to do the factory reset.

     

     

  • Reset the Cisco 8961 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    From the Administrator Settings menu, unlock phone options, then choose Reset Settings > All Settings.

     

  • Reset the Cisco 9951 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    From the Administrator Settings menu, unlock phone options, then choose Reset Settings > All Settings.

     

  • Reset the Cisco 9971 IP Phones to the Factory Default

    Kaynak: www.cisco.com

     

    From the Administrator Settings menu, unlock phone options, then choose Reset Settings > All Settings.